TechnoDocs - User contributions [en]

Drift test

2013-04-08T15:19:22Z

Jglica:

The following tests require version 1.421.50 or newer. On versions prior to 1.423.3, you must have the [[Index pulses]] enabled.

''Upgrades to the Techno CNC Interface can be found at [http://www.technorouters.com/controlinterface.html technorouters.com]''

''We suggest uprgading to a new folder while preserving settings using these instructions: [http://www.docs.technorouters.com/index.php?title=Upgrading_software_into_a_new_folder New Folder Upgrade procedure]''

To test for mechanical drift issues that interfere with machine positioning:

If the [[Index pulses]] are turned on in the software, this process is done automatically every time the system homes in 1.422.1 and higher. So homing the machine, running a file and then re-homing the machine will provide a warning if the machine is suffering from this issue.

Alternately, to force a manual test:

* Prior to running a file, in the main interface, type on the keyboard:

'H' for home

'D' for Drift test

'?' where ? is the axis you suspect of drift (Y,X,Z,A). You should repeat this process for all axes.

* Run a file that will result in the problem. If you choose to [[Test running files|run in the air]], note that this results in reduced forces on the machine, possibly reducing the probability that the problem will occur.

* After the file has run, repeat the original procedure, where in the main interface, type on the keyboard:

'H' for home

'D' for Drift test

'?' where ? is the axis you suspect of drift (Y,X,Z,A). You should repeat this process for all axes.

* You will, after each axis, be presented with a message that states whether or not the system checks out properly.

'''If you get a message that an axis drifted, follow the link for [[Axis drifted]] to investigate the mechanics further.'''

Still not sure what is going on here? Read: [[About drift issues]]

File:0049 GCODE STEPPER DAVINCI.pdf

2013-03-01T15:44:23Z

Jglica:

File:0011 Router Setup for DaVinci.pdf

2013-03-01T15:42:36Z

Jglica:

File:0317 Premium Class Setup Instructions-377.pdf

2013-03-01T14:40:58Z

Jglica:

Scale factors

2013-02-22T19:18:32Z

Jglica:

The scale factors are numbers that represent the smallest increment that can be distinguished per unit length. They're used to inform the software of how much linear distance corresponds to the distance between encoder markers.

Scale factors are printed on the front leg of all new routers.

=== Scale Factor Setup ===

Scale factors can be changed by going to Setup > System, and changing the M1 through M4 scales. A negative sign indicates direction.

[[Media:0274_Scale_Factor_Interface_Setup.pdf|Scale Factor Interface Setup (pdf)]]

* Click on Setup > System
* Find the "Mx Scale" section.
* Change the Scale Factor(s) to the correct value(s) for the machine. See the Scale Factor label on the gantry or front leg for details. Otherwise, see below for a guess.
* Click "OK" to save change

If the scale factors are unavailable, try the following values, depending on your machine:

===LC===
* All axes: -20320

===LC 3024===
* M1: 20320
* M2: -20320
* M3: -20320

===LC plus===
* M1: -12192
* M2: -7620
* M3: -20320

===RG===
* M1: -10160 (most) or -12192 (59"x50")
* M2: -7620 (newer) or -5080 (older)
* M3: -20320

===Premium Class===
* M1: 10160
* M2: 5080
* M3: -20320

If none of these values work, please check your measurement device. Try measuring over a larger, or shorter area for verification.

=== Manual Scale Factor Generation ===

If you are still having problems, perform the following operation:

* Using calipers, measure exactly how far the machine moves when you use jog step to move the machine 1 inch.
* Take the current scale factor value, and divide it by the result you just got. (i.e. 20320 / .9")

The resulting number is the correct scale factor. Repeat this test until you achieve the desired accuracy. The number will likely be a round number.

=== Mathematical Scale Factor Generation ===

On some machines, unusual pulleys have been used. This results in scale factors unlike the typical ones listed above. To obtain an exact scale factor for these, some simple math is necessary.

* Count the number of teeth on the motor pulley and ball screw pulley
* The number of pulses per revolution on a standard motor is 4000.
* The typical screw pitches are 5,10 and 20 mm. Spin the screw once while measuring the distance traveled and ascertain which pitch screw you have.

Using these numbers, you can calculate what the appropriate scale factor is.

Scale Factor for 1 inch = ((1/(screw pitch /25.4))*4000)*(ball screw pulley teeth /motor pulley teeth)
Scale Factor for 1 millimeter = ((1/(screw pitch))*4000)*(ball screw pulley teeth /motor pulley teeth)

So a scale factor for 1" units:
* On a 20mm screw
* With 4000 pulses per rev of the motor
* 20 teeth on the pulley
* 22 teeth on the ball screw

Will be:

((1/(20/25.4))*4000) * (22/20) = 5588

[[Category:Knowledge Base]]
[[Category:Software Manual (servo)]]

Runtime Error

2013-02-21T19:41:01Z

Jglica:

Runtime Errors are generally caused when a conflict between the Techno CNC Interface and the Windows operating system occur.

'''Runtime Error 6: Overflow'''

'''Cause:''' In older versions of the software, this can be caused when G Code calls for a very high tool number (i.e. 253).

'''Solution:''' Change your toolpath settings to use a lower tool number (i.e. 5) or upgrade to the latest version of the Techno CNC Interface at [http://technorouters.com/control_interface.html]

Runtime Error

2013-02-21T19:40:12Z

Jglica: Created page with "Runtime Errors are generally caused when a conflict between the Techno CNC Interface and the Windows operating system occur. == '''Runtime Error 6: Overflow''' == '''Cause:'''..."

Runtime Errors are generally caused when a conflict between the Techno CNC Interface and the Windows operating system occur.

== '''Runtime Error 6: Overflow''' ==

'''Cause:''' In older versions of the software, this can be caused when G Code calls for a very high tool number (i.e. 253).

'''Solution:''' Change your toolpath settings to use a lower tool number (i.e. 5) or upgrade to the latest version of the Techno CNC Interface at [http://technorouters.com/control_interface.html]

Pulses were gained or lost

2013-01-02T20:58:22Z

Jglica:

One of the following errors are received:

[[File:Axis_lost_pulses.jpg]]

[[File:Axis_lost_pulses_2.jpg]]

The error code associated with this problem is: 04052010.

This is a very critical error that can result in a lot of problems:

* Machine drift
* Runaway conditions
* Location problems
* Cut quality issues

The causes of this problem are (in order of probability):

* [[Encoder damage|Broken encoder / Dust on the encoder]] (if the environment is dusty)
* [[Verify control cable|Bent Control Cable pin or damaged cable]] (LC Plus or Premium electronics only, this is NEVER caused by a bent pin on an LC / LP controller)
* Nicked or damaged encoder cable wire

Still not sure what is going on here? Read: [[About drift issues]]

Axis drifted

2013-01-02T20:57:06Z

Jglica:

The following error message (with different numbers/axes) is received:

[[File:Axis_drifted.jpg]]

The error code associated with this message is: 27102010

This error means the machine found the home switch in a much different location than it has previously.

This suggests that something in the system is loose.

Possible loose components for this problem are, in order of probability:

* Pulley on ball screw shaft
* Pulley on motor shaft (if it is a low power or otherwise unkeyed motor shaft)
* Loose home switch or home switch bracket
* Loose ball screw bearings
* Loose ball nut

[[Mark Pulleys|How to check directly for loose pulleys]]

If this error is preceded by the following error message:

[[File:Axis_lost_pulses.jpg]]

The problem is NOT loose mechanics, and you should follow the following route:
[[Pulses were gained or lost|Axis lost pulses error message]]

Note that this error will only come up if the index pulse is enabled on that axis.

Still not sure what is going on here? Read: [[About drift issues]]

Main Page

2012-11-21T19:46:30Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card. The RG Series is a discontinued product.
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
* [[Media:0316_RG_Series_Setup_Instructions-377.pdf|RG Series Basic Setup Instructions]]
* [[Media:0330_Readjusting_the_Ball_Nut_.pdf|Readjusting the Ball Nut]]

|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|HD Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:HD-NCStudio_QuickGuide.pdf|HD Series Quick Setup Guide]]
* [[Media:Techno-HD-Manual.pdf|HD Series Manual]]
* [[Media:Techno-HD_Hand-Held_Contoller.pdf|HD Series Hand Held Controller Manual]]

* [[Media:HD_settings.pdf|HD Series Settings]]
* [[Media:squaring_hd-hds.pdf|HD Series Squaring (Reindication) Guide]]
* [[Media:HD_vacuum_Pump-wiring.pdf|HD Series Vacuum Pump Wiring Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.

* [[Media:0629_Techno-HDS-User-Manual.pdf|HDS Series User Manual]]
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure. The Premium Series is a discontinued product.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Servo DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:ServoDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Servo DaVinici series is identified by a controller enclosure whose status lights are Ready, PC, +5, +25, +48 and round servo motors. Servo DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Stepper DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:StepperDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Stepper DaVinici series is identified by a controller housed in the body of the machine that has an external LED status light indicator and square black servo motors with a knob at the top.Stepper DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0011_Router Setup for DaVinci.pdf|Stepper DaVinci Setup Guide]]
* [[Media:0061_Educational DaVinci Setup.pdf|Education Series Stepper DaVinci Setup Guide]]
* [[Media:0049_GCODE STEPPER DAVINCI.pdf|Stepper DaVinci GCODE Guide]]
* [[Media:0224_Stepper Davinci Trouble Shooting Guide.pdf|Stepper DaVinci Troubleshoting Guide]]
* [[Media:0260_Davinci_Spare_Parts_List.pdf|Stepper DaVinci Spare Parts List]]

|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Inverters / Variable Frequency Drives</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

__NOTOC__
__NOEDITSECTION__

Main Page

2012-11-20T16:01:09Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card. The RG Series is a discontinued product.
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
* [[Media:0316_RG_Series_Setup_Instructions-377.pdf|RG Series Basic Setup Instructions]]
* [[Media:0330_Readjusting_the_Ball_Nut_.pdf|Readjusting the Ball Nut]]

|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|HD Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:HD-NCStudio_QuickGuide.pdf|HD Series Quick Setup Guide]]
* [[Media:Techno-HD-Manual.pdf|HD Series Manual]]
* [[Media:Techno-HD_Hand-Held_Contoller.pdf|HD Series Hand Held Controller Manual]]

* [[Media:HD_settings.pdf|HD Series Settings]]
* [[Media:squaring_hd-hds.pdf|HD Series Squaring (Reindication) Guide]]
* [[Media:HD_vacuum_Pump-wiring.pdf|HD Series Vacuum Pump Wiring Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.

* [[Media:0629_Techno-HDS-User-Manual.pdf|HDS Series User Manual]]
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure. The Premium Series is a discontinued product.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Servo DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:ServoDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Servo DaVinici series is identified by a controller enclosure whose status lights are Ready, PC, +5, +25, +48 and round servo motors. Servo DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Stepper DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:StepperDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Stepper DaVinici series is identified by a controller housed in the body of the machine that has an external LED status light indicator and square black servo motors with a knob at the top.Stepper DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0011_Router Setup for DaVinci.pdf|Stepper DaVinci Setup Guide]]
* [[Media:0061_Educational DaVinci Setup.pdf|Education Series Stepper DaVinci Setup Guide]]
* [[Media:0049_GCODE STEPPER DAVINCI.pdf|Stepper DaVinci GCODE Guide]]
* [[Media:0224_Stepper Davinci Trouble Shooting Guide.pdf|Stepper DaVinci Troubleshoting Guide]]
* [[Media:0260_Davinci_Spare_Parts_List.pdf|Stepper DaVinci Spare Parts List]]

|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Inverters / Variable Frequency Drives</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

__NOTOC__
__NOEDITSECTION__

File:0629 Techno-HDS-User-Manual.pdf

2012-11-20T16:00:42Z

Jglica:

MediaWiki:Sidebar

2012-10-31T17:07:01Z

Jglica:

MediaWiki:Sidebar

2012-10-31T17:04:49Z

Jglica:

MediaWiki:Sidebar

2012-10-31T17:03:27Z

Jglica:

Main Page

2012-10-31T15:13:00Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card. The RG Series is a discontinued product.
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
* [[Media:0316_RG_Series_Setup_Instructions-377.pdf|RG Series Basic Setup Instructions]]
* [[Media:0330_Readjusting_the_Ball_Nut_.pdf|Readjusting the Ball Nut]]

|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|HD Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:HD-NCStudio_QuickGuide.pdf|HD Series Quick Setup Guide]]
* [[Media:Techno-HD-Manual.pdf|HD Series Manual]]
* [[Media:Techno-HD_Hand-Held_Contoller.pdf|HD Series Hand Held Controller Manual]]

* [[Media:HD_settings.pdf|HD Series Settings]]
* [[Media:squaring_hd-hds.pdf|HD Series Squaring (Reindication) Guide]]
* [[Media:HD_vacuum_Pump-wiring.pdf|HD Series Vacuum Pump Wiring Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure. The Premium Series is a discontinued product.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Servo DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:ServoDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Servo DaVinici series is identified by a controller enclosure whose status lights are Ready, PC, +5, +25, +48 and round servo motors. Servo DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Stepper DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:StepperDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Stepper DaVinici series is identified by a controller housed in the body of the machine that has an external LED status light indicator and square black servo motors with a knob at the top.Stepper DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0011_Router Setup for DaVinci.pdf|Stepper DaVinci Setup Guide]]
* [[Media:0061_Educational DaVinci Setup.pdf|Education Series Stepper DaVinci Setup Guide]]
* [[Media:0049_GCODE STEPPER DAVINCI.pdf|Stepper DaVinci GCODE Guide]]
* [[Media:0224_Stepper Davinci Trouble Shooting Guide.pdf|Stepper DaVinci Troubleshoting Guide]]
* [[Media:0260_Davinci_Spare_Parts_List.pdf|Stepper DaVinci Spare Parts List]]

|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Inverters / Variable Frequency Drives</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

__NOTOC__
__NOEDITSECTION__

File:Techno-HD Hand-Held Contoller.pdf

2012-10-31T15:12:10Z

Jglica: uploaded a new version of "File:Techno-HD Hand-Held Contoller.pdf"

Main Page

2012-10-31T14:45:24Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card. The RG Series is a discontinued product.
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
* [[Media:0316_RG_Series_Setup_Instructions-377.pdf|RG Series Basic Setup Instructions]]
* [[Media:0330_Readjusting_the_Ball_Nut_.pdf|Readjusting the Ball Nut]]

|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|HD Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:HD-NCStudio_QuickGuide.pdf|HD Series Quick Setup Guide]]
* [[Media:Techno-HD-Manual.pdf|HD Series Manual]]
* [[Media:HD_settings.pdf|HD Series Settings]]
* [[Media:squaring_hd-hds.pdf|HD Series Squaring (Reindication) Guide]]
* [[Media:HD_vacuum_Pump-wiring.pdf|HD Series Vacuum Pump Wiring Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure. The Premium Series is a discontinued product.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Servo DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:ServoDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Servo DaVinici series is identified by a controller enclosure whose status lights are Ready, PC, +5, +25, +48 and round servo motors. Servo DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Stepper DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:StepperDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Stepper DaVinici series is identified by a controller housed in the body of the machine that has an external LED status light indicator and square black servo motors with a knob at the top.Stepper DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0011_Router Setup for DaVinci.pdf|Stepper DaVinci Setup Guide]]
* [[Media:0061_Educational DaVinci Setup.pdf|Education Series Stepper DaVinci Setup Guide]]
* [[Media:0049_GCODE STEPPER DAVINCI.pdf|Stepper DaVinci GCODE Guide]]
* [[Media:0224_Stepper Davinci Trouble Shooting Guide.pdf|Stepper DaVinci Troubleshoting Guide]]
* [[Media:0260_Davinci_Spare_Parts_List.pdf|Stepper DaVinci Spare Parts List]]

|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Inverters / Variable Frequency Drives</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

__NOTOC__
__NOEDITSECTION__

Main Page

2012-10-31T14:44:26Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card. The RG Series is a discontinued product.
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
* [[Media:0316_RG_Series_Setup_Instructions-377.pdf|RG Series Basic Setup Instructions]]
* [[Media:0330_Readjusting_the_Ball_Nut_.pdf|Readjusting the Ball Nut]]

|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|HD Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:HD-NCStudio_QuickGuide.pdf|HD Series Quick Setup Guide]]
* [[Media:Techno-HD-Manual.pdf|HD Series Manual]]
* [[Media:HD_settings.pdf|HD Series Settings]]
* [[Media:squaring_hd-hds.pdf|HD Series Squaring (Reindication) Guide]]
* [[Media:HD_vacuum_Pump-wiring.pdf|HD Series Vacuum Pump Wiring Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure. The Premium Series is a discontinued product.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Servo DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:ServoDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Servo DaVinici series is identified by a controller enclosure whose status lights are Ready, PC, +5, +25, +48 and round servo motors. Servo DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Stepper DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:StepperDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Stepper DaVinici series is identified by a controller housed in the body of the machine that has an external LED status light indicator and square black servo motors with a knob at the top.Stepper DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0011_Router Setup for DaVinci.pdf|Stepper DaVinci Setup Guide]]
* [[Media:0061_Educational DaVinci Setup.pdf|Education Series Stepper DaVinci Setup Guide]]
* [[Media:0049_GCODE STEPPER DAVINCI.pdf|Stepper DaVinci GCODE Guide]]
* [[Media:0224_Stepper Davinci Trouble Shooting Guide.pdf|Stepper DaVinci Troubleshoting Guide]]
* [[Media:0260_Davinci_Spare_Parts_List.pdf|Stepper DaVinci Spare Parts List]]

|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Inverters / Variable Frequency Drives</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

__NOTOC__
__NOEDITSECTION__

File:0410 LC Plus Setup Instructions - 051507.pdf

2012-10-31T14:42:47Z

Jglica:

Main Page

2012-10-31T13:59:47Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:HD-NCStudio_QuickGuide.pdf|HD Series Quick Setup Guide]]
* [[Media:Techno-HD-Manual.pdf|HD Series Manual]]
* [[Media:HD_settings.pdf|HD Series Settings]]
* [[Media:squaring_hd-hds.pdf|HD Series Squaring (Reindication) Guide]]
* [[Media:HD_vacuum_Pump-wiring.pdf|HD Series Vacuum Pump Wiring Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Servo DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:ServoDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Servo DaVinici series is identified by a controller enclosure whose status lights are Ready, PC, +5, +25, +48 and round servo motors. Servo DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0439_Techno_CNC_Servo_G-Code_Interface_Manual_-_Build_400.pdf|Techno CNC Interface Manual]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Stepper DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:StepperDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Stepper DaVinici series is identified by a controller housed in the body of the machine that has an external LED status light indicator and square black servo motors with a knob at the top.Stepper DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0011_Router Setup for DaVinci.pdf|Stepper DaVinci Setup Guide]]
* [[Media:0061_Educational DaVinci Setup.pdf|Education Series Stepper DaVinci Setup Guide]]
* [[Media:0049_GCODE STEPPER DAVINCI.pdf|Stepper DaVinci GCODE Guide]]
* [[Media:0224_Stepper Davinci Trouble Shooting Guide.pdf|Stepper DaVinci Troubleshoting Guide]]
* [[Media:0260_Davinci_Spare_Parts_List.pdf|Stepper DaVinci Spare Parts List]]

|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Inverters / Variable Frequency Drives</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

__NOTOC__
__NOEDITSECTION__

File:Techno-HD-Manual.pdf

2012-10-31T13:55:07Z

Jglica:

File:HD vacuum Pump-wiring.pdf

2012-10-31T13:52:23Z

Jglica: uploaded a new version of "File:HD vacuum Pump-wiring.pdf"

File:0260 Davinci Spare Parts List.pdf

2012-09-13T13:10:28Z

Jglica: uploaded a new version of "File:0260 Davinci Spare Parts List.pdf"

File:0260 Davinci Spare Parts List.pdf

2012-09-11T15:30:34Z

Jglica: uploaded a new version of "File:0260 Davinci Spare Parts List.pdf"

File:Squaring hd-hds.pdf

2012-09-11T15:12:49Z

Jglica:

Main Page

2012-09-11T14:31:07Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:HD-NCStudio_QuickGuide.pdf|HD Series Quick Setup Guide]]
* [[Media:HD_Stepper_Controller_V4.pdf|HD Series Manual]]
* [[Media:HD_settings.pdf|HD Series Settings]]
* [[Media:squaring_hd-hds.pdf|HD Series Squaring (Reindication) Guide]]
* [[Media:HD_vacuum_Pump-wiring.pdf|HD Series Vacuum Pump Wiring Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Servo DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:ServoDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Servo DaVinici series is identified by a controller enclosure whose status lights are Ready, PC, +5, +25, +48 and round servo motors. Servo DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Stepper DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:StepperDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Stepper DaVinici series is identified by a controller housed in the body of the machine that has an external LED status light indicator and square black servo motors with a knob at the top.Stepper DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0011_Router Setup for DaVinci.pdf|Stepper DaVinci Setup Guide]]
* [[Media:0061_Educational DaVinci Setup.pdf|Education Series Stepper DaVinci Setup Guide]]
* [[Media:0049_GCODE STEPPER DAVINCI.pdf|Stepper DaVinci GCODE Guide]]
* [[Media:0224_Stepper Davinci Trouble Shooting Guide.pdf|Stepper DaVinci Troubleshoting Guide]]
* [[Media:0260_Davinci_Spare_Parts_List.pdf|Stepper DaVinci Spare Parts List]]

|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Inverters / Variable Frequency Drives</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

__NOTOC__
__NOEDITSECTION__

Main Page

2012-09-11T14:25:54Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Servo DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:ServoDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Servo DaVinici series is identified by a controller enclosure whose status lights are Ready, PC, +5, +25, +48 and round servo motors. Servo DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Stepper DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:StepperDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Stepper DaVinici series is identified by a controller housed in the body of the machine that has an external LED status light indicator and square black servo motors with a knob at the top.Stepper DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0011_Router Setup for DaVinci.pdf|Stepper DaVinci Setup Guide]]
* [[Media:0061_Educational DaVinci Setup.pdf|Education Series Stepper DaVinci Setup Guide]]
* [[Media:0049_GCODE STEPPER DAVINCI.pdf|Stepper DaVinci GCODE Guide]]
* [[Media:0224_Stepper Davinci Trouble Shooting Guide.pdf|Stepper DaVinci Troubleshoting Guide]]
* [[Media:0260_Davinci_Spare_Parts_List.pdf|Stepper DaVinci Spare Parts List]]

|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Inverters / Variable Frequency Drives</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

__NOTOC__
__NOEDITSECTION__

Main Page

2012-09-11T14:25:08Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Servo DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:ServoDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Servo DaVinici series is identified by a controller enclosure whose status lights are Ready, PC, +5, +25, +48 and round servo motors. Servo DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Stepper DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:StepperDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Stepper DaVinici series is identified by a controller housed in the body of the machine that has an external LED status light indicator and square black servo motors with a knob at the top.Stepper DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0011_Router Setup for DaVinci.pdf|Stepper DaVinci Setup Guide]]
* [[Media:0061_Educational DaVinci Setup.pdf|Education Series Stepper DaVinci Setup Guide]]
* [[Media:0049_GCODE STEPPER DAVINCI.pdf|Stepper DaVinci GCODE Guide]]
* [[Media:0224_Stepper Davinci Trouble Shooting Guide.pdf|Stepper DaVinci Troubleshoting Guide]]
* [[Media:0260_Davinci_Spare_Parts_List.pdf|Stepper DaVinci Spare Parts List]]

|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Inverters / Variable Frequency Drives</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

__NOTOC__
__NOEDITSECTION__

Main Page

2012-09-11T14:17:44Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:HD_settings.pdf|General HD Machine Settings]]
* [[Media:HD_Stepper_Controller_V4.pdf|General HD Machine Manual]]
* [[Media:HD-NCStudio_QuickGuide.pdf|NC Studio for HD Machine Quick Guide]]
* [[Media:Squaring_hd-hds.pdf|HD Machine Reindication (Squaring) Guide]]
* [[Media:HD_vacuum_Pump-wiring.pdf|HD Machine Vacuum Pump Wiring]]
|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Servo DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:ServoDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Servo DaVinici series is identified by a controller enclosure whose status lights are Ready, PC, +5, +25, +48 and round servo motors. Servo DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Stepper DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:StepperDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Stepper DaVinici series is identified by a controller housed in the body of the machine that has an external LED status light indicator and square black servo motors with a knob at the top.Stepper DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0011_Router Setup for DaVinci.pdf|Stepper DaVinci Setup Guide]]
* [[Media:0061_Educational DaVinci Setup.pdf|Education Series Stepper DaVinci Setup Guide]]
* [[Media:0049_GCODE STEPPER DAVINCI.pdf|Stepper DaVinci GCODE Guide]]
* [[Media:0224_Stepper Davinci Trouble Shooting Guide.pdf|Stepper DaVinci Troubleshoting Guide]]

|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Inverters / Variable Frequency Drives</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

--------- OLD HEADER SECTION -----------------

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Software & Hardware Manuals</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | IMAGE
| valign="top" |
* [[Software manual|Software Manuals]]
* [[Hardware Manual|Hardware Manuals]]
* [[Machine Setup Guides]]
* [[File:Machine Maintenance Manual.pdf]]
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Tips & Tutorials</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | Coming Soon! Submit tips with our [http://www.technorouters.com/feedback.php Feedback form]!

([[Tips and Tutorials|Tips & Tutorials Main Page]])
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Troubleshooting</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" |
* [[Troubleshooting|Knowledge base main]]
* [[FAQ|Frequently Asked Questions (FAQ)]]
|}
</div>
|}

=== About Techno Docs ===

This site aims to collect all the documentation in one easy-to-access location for everyone who uses or works on a Techno machine. We're currently in Beta, which means not everything is available online, and some information may be misleading. That's a work in progress.

As soon as we feel comfortable with the amount and quality of the information here, we'll remove the BETA tag on the logo, and you can feel comfortable knowing the information has been checked and is accurate.

If you notice anything that doesn't seem to correlate to your experience, please send us an email! We aim to fix problems quickly. If you have an idea about something that would be helpful to you, please contact us so we can get it online.

Thanks!

__NOTOC__
__NOEDITSECTION__

File:HD vacuum Pump-wiring.pdf

2012-09-11T14:14:23Z

Jglica:

File:HD-NCStudio QuickGuide.pdf

2012-09-11T14:11:39Z

Jglica:

File:HD settings.pdf

2012-09-11T14:10:46Z

Jglica: uploaded a new version of "File:HD settings.pdf"

Main Page

2012-08-29T14:20:56Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Servo DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:ServoDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Servo DaVinici series is identified by a controller enclosure whose status lights are Ready, PC, +5, +25, +48 and round servo motors. Servo DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Stepper DaVinci Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:StepperDavinciSeriesBox.png|left|Servo DaVinci Series.]]
| valign="top" |

The Stepper DaVinici series is identified by a controller housed in the body of the machine that has an external LED status light indicator and square black servo motors with a knob at the top.Stepper DaVinci machines are sometimes in an enclosure but have been made in tabletop styles.
* [[Media:0011_Router Setup for DaVinci.pdf|Stepper DaVinci Setup Guide]]
* [[Media:0061_Educational DaVinci Setup.pdf|Education Series Stepper DaVinci Setup Guide]]
* [[Media:0049_GCODE STEPPER DAVINCI.pdf|Stepper DaVinci GCODE Guide]]
* [[Media:0224_Stepper Davinci Trouble Shooting Guide.pdf|Stepper DaVinci Troubleshoting Guide]]

|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Inverters / Variable Frequency Drives</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

--------- OLD HEADER SECTION -----------------

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Software & Hardware Manuals</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | IMAGE
| valign="top" |
* [[Software manual|Software Manuals]]
* [[Hardware Manual|Hardware Manuals]]
* [[Machine Setup Guides]]
* [[File:Machine Maintenance Manual.pdf]]
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Tips & Tutorials</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | Coming Soon! Submit tips with our [http://www.technorouters.com/feedback.php Feedback form]!

([[Tips and Tutorials|Tips & Tutorials Main Page]])
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Troubleshooting</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" |
* [[Troubleshooting|Knowledge base main]]
* [[FAQ|Frequently Asked Questions (FAQ)]]
|}
</div>
|}

=== About Techno Docs ===

This site aims to collect all the documentation in one easy-to-access location for everyone who uses or works on a Techno machine. We're currently in Beta, which means not everything is available online, and some information may be misleading. That's a work in progress.

As soon as we feel comfortable with the amount and quality of the information here, we'll remove the BETA tag on the logo, and you can feel comfortable knowing the information has been checked and is accurate.

If you notice anything that doesn't seem to correlate to your experience, please send us an email! We aim to fix problems quickly. If you have an idea about something that would be helpful to you, please contact us so we can get it online.

Thanks!

__NOTOC__
__NOEDITSECTION__

Main Page

2012-08-29T14:12:17Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">Premium Class Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

--------- OLD HEADER SECTION -----------------

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Software & Hardware Manuals</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | IMAGE
| valign="top" |
* [[Software manual|Software Manuals]]
* [[Hardware Manual|Hardware Manuals]]
* [[Machine Setup Guides]]
* [[File:Machine Maintenance Manual.pdf]]
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Tips & Tutorials</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | Coming Soon! Submit tips with our [http://www.technorouters.com/feedback.php Feedback form]!

([[Tips and Tutorials|Tips & Tutorials Main Page]])
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Troubleshooting</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" |
* [[Troubleshooting|Knowledge base main]]
* [[FAQ|Frequently Asked Questions (FAQ)]]
|}
</div>
|}

=== About Techno Docs ===

This site aims to collect all the documentation in one easy-to-access location for everyone who uses or works on a Techno machine. We're currently in Beta, which means not everything is available online, and some information may be misleading. That's a work in progress.

As soon as we feel comfortable with the amount and quality of the information here, we'll remove the BETA tag on the logo, and you can feel comfortable knowing the information has been checked and is accurate.

If you notice anything that doesn't seem to correlate to your experience, please send us an email! We aim to fix problems quickly. If you have an idea about something that would be helpful to you, please contact us so we can get it online.

Thanks!

__NOTOC__
__NOEDITSECTION__

Main Page

2012-08-29T13:42:06Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

--------- OLD HEADER SECTION -----------------

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Software & Hardware Manuals</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | IMAGE
| valign="top" |
* [[Software manual|Software Manuals]]
* [[Hardware Manual|Hardware Manuals]]
* [[Machine Setup Guides]]
* [[File:Machine Maintenance Manual.pdf]]
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Tips & Tutorials</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | Coming Soon! Submit tips with our [http://www.technorouters.com/feedback.php Feedback form]!

([[Tips and Tutorials|Tips & Tutorials Main Page]])
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Troubleshooting</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" |
* [[Troubleshooting|Knowledge base main]]
* [[FAQ|Frequently Asked Questions (FAQ)]]
|}
</div>
|}

=== About Techno Docs ===

This site aims to collect all the documentation in one easy-to-access location for everyone who uses or works on a Techno machine. We're currently in Beta, which means not everything is available online, and some information may be misleading. That's a work in progress.

As soon as we feel comfortable with the amount and quality of the information here, we'll remove the BETA tag on the logo, and you can feel comfortable knowing the information has been checked and is accurate.

If you notice anything that doesn't seem to correlate to your experience, please send us an email! We aim to fix problems quickly. If you have an idea about something that would be helpful to you, please contact us so we can get it online.

Thanks!

__NOTOC__
__NOEDITSECTION__

Main Page

2012-08-29T13:40:24Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:PremiumSeriesBox.png|left|Premium Series.]]
| valign="top" |

The Premium Series is identified by square black or blue servo motors and a free standing or wheeled controller enclosure.
* [[Media:0317_Premium Class Setup Instructions-377.pdf|Premium Class Basic Setup Instructions]]
* [[Media:0319_Premium Class Lubrication Instructions.pdf|Premium Class Lubrication Guide]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|General Machine Maintenance Guide]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

--------- OLD HEADER SECTION -----------------

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Software & Hardware Manuals</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | IMAGE
| valign="top" |
* [[Software manual|Software Manuals]]
* [[Hardware Manual|Hardware Manuals]]
* [[Machine Setup Guides]]
* [[File:Machine Maintenance Manual.pdf]]
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Tips & Tutorials</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | Coming Soon! Submit tips with our [http://www.technorouters.com/feedback.php Feedback form]!

([[Tips and Tutorials|Tips & Tutorials Main Page]])
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Troubleshooting</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" |
* [[Troubleshooting|Knowledge base main]]
* [[FAQ|Frequently Asked Questions (FAQ)]]
|}
</div>
|}

=== About Techno Docs ===

This site aims to collect all the documentation in one easy-to-access location for everyone who uses or works on a Techno machine. We're currently in Beta, which means not everything is available online, and some information may be misleading. That's a work in progress.

As soon as we feel comfortable with the amount and quality of the information here, we'll remove the BETA tag on the logo, and you can feel comfortable knowing the information has been checked and is accurate.

If you notice anything that doesn't seem to correlate to your experience, please send us an email! We aim to fix problems quickly. If you have an idea about something that would be helpful to you, please contact us so we can get it online.

Thanks!

__NOTOC__
__NOEDITSECTION__

File:CPMSeriesBox.png

2012-08-27T18:08:35Z

Jglica:

File:PremiumSeriesBox.png

2012-08-27T18:08:09Z

Jglica:

File:ServoDavinciSeriesBox.png

2012-08-27T18:06:37Z

Jglica:

File:StepperDavinciSeriesBox.png

2012-08-27T18:06:10Z

Jglica:

Main Page

2012-08-23T18:57:37Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|dsasdasasd|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

--------- OLD HEADER SECTION -----------------

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Software & Hardware Manuals</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | IMAGE
| valign="top" |
* [[Software manual|Software Manuals]]
* [[Hardware Manual|Hardware Manuals]]
* [[Machine Setup Guides]]
* [[File:Machine Maintenance Manual.pdf]]
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Tips & Tutorials</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | Coming Soon! Submit tips with our [http://www.technorouters.com/feedback.php Feedback form]!

([[Tips and Tutorials|Tips & Tutorials Main Page]])
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Troubleshooting</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" |
* [[Troubleshooting|Knowledge base main]]
* [[FAQ|Frequently Asked Questions (FAQ)]]
|}
</div>
|}

=== About Techno Docs ===

This site aims to collect all the documentation in one easy-to-access location for everyone who uses or works on a Techno machine. We're currently in Beta, which means not everything is available online, and some information may be misleading. That's a work in progress.

As soon as we feel comfortable with the amount and quality of the information here, we'll remove the BETA tag on the logo, and you can feel comfortable knowing the information has been checked and is accurate.

If you notice anything that doesn't seem to correlate to your experience, please send us an email! We aim to fix problems quickly. If you have an idea about something that would be helpful to you, please contact us so we can get it online.

Thanks!

__NOTOC__
__NOEDITSECTION__

Main Page

2012-08-23T18:55:06Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCPlusSeriesBox.png|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RGSeriesBox.png|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

--------- OLD HEADER SECTION -----------------

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Software & Hardware Manuals</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | IMAGE
| valign="top" |
* [[Software manual|Software Manuals]]
* [[Hardware Manual|Hardware Manuals]]
* [[Machine Setup Guides]]
* [[File:Machine Maintenance Manual.pdf]]
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Tips & Tutorials</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | Coming Soon! Submit tips with our [http://www.technorouters.com/feedback.php Feedback form]!

([[Tips and Tutorials|Tips & Tutorials Main Page]])
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Troubleshooting</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" |
* [[Troubleshooting|Knowledge base main]]
* [[FAQ|Frequently Asked Questions (FAQ)]]
|}
</div>
|}

=== About Techno Docs ===

This site aims to collect all the documentation in one easy-to-access location for everyone who uses or works on a Techno machine. We're currently in Beta, which means not everything is available online, and some information may be misleading. That's a work in progress.

As soon as we feel comfortable with the amount and quality of the information here, we'll remove the BETA tag on the logo, and you can feel comfortable knowing the information has been checked and is accurate.

If you notice anything that doesn't seem to correlate to your experience, please send us an email! We aim to fix problems quickly. If you have an idea about something that would be helpful to you, please contact us so we can get it online.

Thanks!

__NOTOC__
__NOEDITSECTION__

File:LCSeriesBox.png

2012-08-23T18:53:03Z

Jglica: uploaded a new version of "File:LCSeriesBox.png"

File:LCSeriesBox.png

2012-08-23T18:51:41Z

Jglica:

Main Page

2012-08-23T18:51:07Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCSeriesBox.png|left|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCX_Router_210x150.jpg|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RG-MACHINE-2.jpg|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

--------- OLD HEADER SECTION -----------------

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Software & Hardware Manuals</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | IMAGE
| valign="top" |
* [[Software manual|Software Manuals]]
* [[Hardware Manual|Hardware Manuals]]
* [[Machine Setup Guides]]
* [[File:Machine Maintenance Manual.pdf]]
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Tips & Tutorials</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | Coming Soon! Submit tips with our [http://www.technorouters.com/feedback.php Feedback form]!

([[Tips and Tutorials|Tips & Tutorials Main Page]])
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Troubleshooting</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" |
* [[Troubleshooting|Knowledge base main]]
* [[FAQ|Frequently Asked Questions (FAQ)]]
|}
</div>
|}

=== About Techno Docs ===

This site aims to collect all the documentation in one easy-to-access location for everyone who uses or works on a Techno machine. We're currently in Beta, which means not everything is available online, and some information may be misleading. That's a work in progress.

As soon as we feel comfortable with the amount and quality of the information here, we'll remove the BETA tag on the logo, and you can feel comfortable knowing the information has been checked and is accurate.

If you notice anything that doesn't seem to correlate to your experience, please send us an email! We aim to fix problems quickly. If you have an idea about something that would be helpful to you, please contact us so we can get it online.

Thanks!

__NOTOC__
__NOEDITSECTION__

File:RGSeriesBox.png

2012-08-23T18:48:49Z

Jglica:

File:LCPlusSeriesBox.png

2012-08-23T18:48:26Z

Jglica:

Main Page

2012-08-07T19:28:21Z

Jglica:

{| id="mp-topbanner" style="width:100%; background:#f6f6f6; margin-top:1.2em; border:1px solid #ddd;"
| style="width:61%; color:#000;" |
{| style="width:280px; border:none; background:none;"
| style="width:280px; text-align:center; white-space:nowrap; color:#000;" |
<div style="font-size:162%; border:none; margin:0; padding:.1em; color:#000;">Welcome to Techno Docs</div>
<div style="top:+0.2em; font-size:95%;">Documentation, Setup Instructions and Schematics for Techno CNC Machines</div>
|}
|}
This section is organized by machine / controller type. Though several machines may look similar visually, they are run by very different controllers. Make sure you identify your controller type using the available pictures of machine and controller box.

Please keep in mind that this section is expanding and is not yet complete. As we move forward, we'll remove the BETA logo from this site. If you find any information that is irrelevant or incorrect, please do not hesitate to let us know by emailing us at support@technorouters.com with the specific page that is incorrect.
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">LC Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCrouter.jpg|left|LC Series.]]
| valign="top" |

The LC Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, PC, +5, +24, +48.
* [[Media:0481_LC Series Basic Setup Instructions-Build 400+.pdf|LC Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0229_LC and Lathe Board-Callouts-Connectors.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">LC+ / LCX Series Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:LCX_Router_210x150.jpg|left|LC+ / LCX.]]
| valign="top" |

The LC + / LCX Controller Series is usually identified by a painted grayish white control box with a black display badge that reads Ready, Brake, Axis 0, Axis 1, Axis 2. This kind of controller uses a long (~9") PCI Card.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]

* [[Media:TechnoCNCInterfaceManual.pdf|Techno CNC Interface Manual]]
|}
</div>
{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">RG Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:RG-MACHINE-2.jpg|left|RG Series.]]
| valign="top" |

The RG (Servo Box 1, Servo Box 2) Controller Series is usually identified by a aluminum controller box which usually has four doors on its front. Usually at least three of the front doors will have a hole through which a green LED light shines through. This kind of controller uses a long (~9") PCI Card.
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HD / HD Mini Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HD_HDMini.jpg|left|LC Series.]]
| valign="top" |

The HD Micro Stepper Controller is identified by a freestanding tower which houses the Controller, Variable Frequency Drive, Amplifiers, Fuses and Breakers. The HD Controller does not require a PC for operation. It is operated using a handheld control pendant with a built-in USB port. The HD Mini Controller is fully self-enclosed but it still uses the same handheld control pendant.
* [[Media:0410_LC_Plus_Setup_Instructions_-_051507.pdf|LC+ / LCX Series Basic Setup Instructions]]
* [[Media:0326_Techno_CNC_Router_Reindication_Instructions.pdf|Reindication (Machine Suquaring) Guide]]
* [[Media:0403_MP-HP Servo Controller 3 Motherboard Reference-2009.pdf|Control Board Diagram]]
* [[Media:0320_Machine Maintenance Manual-June 2010.pdf|Machine Maintenance Manual]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:HDSSeries.jpg|left|LC Series.]]
| valign="top" |

The HDS Controller is identified by a large freestanding tower which houses the PC, OSAI Controller, Variable Frequency Drive, Amplifiers, Fuses, Breakers, Etc.
* [[Media:Osai_STARTUP_Procedure_v3.pdf|Startup Procedure]]
* [[Media:HDS_Quickguide_Flowcharts.pdf|Quick Guide with Flowcharts]]
* [[Media:HDS_Screen_CalloutsV2.pdf|Main Interface Screen Callouts]]
* [[Media:HDS_Tool_Stand_Tutorial.pdf|Tool Stand Learning Tutorial]]
* [[Media:HDS_Osai_GCODE_GUIDE.pdf|GCODE Guide for Osai Controller]]
* [[Media:HD_HDS_Reindication.pdf|Reindication (Machine Suquaring) Guide]]
|}
</div>

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
<div class="mainpage_hubtitle">HDS Series</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | [[File:invertertypes.jpg|left|Inverters / Variable Frequency Drives]]
| valign="top" |

Inverters (Variable Frequency Drives) are responsible for powering the spindle and sometimes a vacuum pump. Over the years, Techno has used Motortronics, Telemechanique and Schneider Electric brands.
* [[Media:UM312_en.pdf|Altivar 312 General Programming & Troubleshooting Guide (Telemechanique / Schneider Electric)]]

|}
</div>

--------- OLD HEADER SECTION -----------------

{| style="border:0; margin: 0;" width="100%" cellspacing="10"
| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Software & Hardware Manuals</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | IMAGE
| valign="top" |
* [[Software manual|Software Manuals]]
* [[Hardware Manual|Hardware Manuals]]
* [[Machine Setup Guides]]
* [[File:Machine Maintenance Manual.pdf]]
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Tips & Tutorials</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" | Coming Soon! Submit tips with our [http://www.technorouters.com/feedback.php Feedback form]!

([[Tips and Tutorials|Tips & Tutorials Main Page]])
|}
</div>

| valign="top" class="mainpage_hubbox" |
<div class="mainpage_hubtitle">Troubleshooting</div>
<div class="mainpage_boxcontents">
{| style="border: 0; margin: 0;" cellpadding="3"
| valign="top" |
* [[Troubleshooting|Knowledge base main]]
* [[FAQ|Frequently Asked Questions (FAQ)]]
|}
</div>
|}

=== About Techno Docs ===

This site aims to collect all the documentation in one easy-to-access location for everyone who uses or works on a Techno machine. We're currently in Beta, which means not everything is available online, and some information may be misleading. That's a work in progress.

As soon as we feel comfortable with the amount and quality of the information here, we'll remove the BETA tag on the logo, and you can feel comfortable knowing the information has been checked and is accurate.

If you notice anything that doesn't seem to correlate to your experience, please send us an email! We aim to fix problems quickly. If you have an idea about something that would be helpful to you, please contact us so we can get it online.

Thanks!

__NOTOC__
__NOEDITSECTION__

File:TechnoCNCInterfaceManual.pdf

2012-08-07T19:26:47Z

Jglica: