All Axes are frozen - Revision history

Mfrost: /* Solution */

2010-10-13T20:49:30Z

‎Solution

2010-10-13T20:44:59Z

‎Solution

2010-10-13T20:44:09Z

‎Solution

2010-10-13T20:43:25Z

2010-10-13T19:29:43Z

‎Possible Causes

2010-10-13T19:28:47Z

‎Possible Causes

2010-10-13T19:28:04Z

‎Possible Causes

2010-10-13T19:27:35Z

‎Possible Causes

2010-10-13T18:56:00Z

‎Possible Causes

2010-10-13T18:55:37Z

‎Scenario

@@ Line 17: / Line 17: @@
 :2) Clean and re-seat the SCSI connector, starting with the end connecting to the PC. Test the cable for continuity with a multimeter.
 :3) Check Device Manager and verify PCI card is working. If not, reinstall driver and/or re-seat the card in the PCI slot.
 :4) If you suspect the controller mainboard is not functioning properly, contact Techno's Technical Support department.
 [[Category:Knowledge Base]]

@@ Line 17: / Line 17: @@
 :2) Clean and re-seat the SCSI connector, starting with the end connecting to the PC. Test the cable for continuity with a multimeter.
 :3) Check Device Manager and verify PCI card is working. If not, reinstall driver and/or re-seat the card in the PCI slot.
-:4) If you suspect the controller mainboard is not functioning properly, contact Techno's free Technical Support department.
+:4) If you suspect the controller mainboard is not functioning properly, contact Techno's Technical Support department.
 [[Category:Knowledge Base]]

@@ Line 14: / Line 14: @@
 === Solution ===
-:1) Turn the router's Controller "ON", and verify that the controller's LED lights are ALL "Lit" and the controller is "ON"
+:1) Turn the router's Controller "ON", and verify that ALL the controller's LED lights are "Lit" and the controller is "ON"
 :2) Clean and re-seat the SCSI connector, starting with the end connecting to the PC. Test the cable for continuity with a multimeter.
 :3) Check Device Manager and verify PCI card is working. If not, reinstall driver and/or re-seat the card in the PCI slot.

← Older revision		Revision as of 20:43, 13 October 2010
Line 1:		Line 1:
−	All axes are frozen (i.e. will not move for some reason.)	+	All axes are frozen (i.e. will not move for some reason) but CAN be moved manually

	=== Scenario ===		=== Scenario ===

@@ Line 11: / Line 11: @@
 :2) The SCSI cable, for some reason, is not making the required connection between the PC to the controller.
 :3) The [[Computer card]] is either not functioning or not properly installed
-:4) The controller's [[Mainboard]] is not functioning.
+:4) The [[Controller mainboard]] is not functioning.
 === Solution ===

@@ Line 10: / Line 10: @@
 :1) It is possible the router's controller is simply not powered up.
 :2) The SCSI cable, for some reason, is not making the required connection between the PC to the controller.
-:3) The [[PCI cards]] either not functioning or not properly installed
+:3) The [[PCI Cards]] either not functioning or not properly installed
 :4) The controller's [[Mainboard]] is not functioning.

@@ Line 8: / Line 8: @@
 === Possible Causes ===
-:1) It is possible the router controller is simply not powered up.
+:1) It is possible the router's controller is simply not powered up.
 :2) The SCSI cable, for some reason, is not making the required connection between the PC to the controller.
 :3) The [[PCI card]] is either not functioning or not properly installed

@@ Line 3: / Line 3: @@
 === Scenario ===
-* '''All Axes''' will not move via interface and '''cannot be moved manually'''.
+* '''All Axes''' will not move via interface or when running an NC file'''.
 * Receives multiple "M-x Position error, no power to controller. Re-enable controller?", circular error