Controller Not Enabled - Revision history

Efeldman at 19:38, 1 September 2011

2011-09-01T19:38:23Z

2011-09-01T15:57:26Z

2011-09-01T15:52:47Z

2011-09-01T15:51:14Z

2011-09-01T15:29:13Z

Created page with "If you are repeatedly getting one of the following two message boxes:"

New page

If you are repeatedly getting one of the following two message boxes:

@@ Line 21: / Line 21: @@
 If your control box has a ready light, '''while watching the ready light, click to enable the controller'''. The '''exact moment''' you click to enable, the ready light may blink.
 '''You may need an assistant to click to enable while you watch the ready light.'''
 If the ready light blinks one time like this (this video cycles every 10 seconds, be patient):

@@ Line 24: / Line 24: @@
 If the ready light blinks one time like this (this video cycles every 10 seconds, be patient):
-[[Image:Estop_blink.jpg]]
+[[Image:Estop_blink.gif]]
 The problem is the E-stop loop.

@@ Line 5: / Line 5: @@
 [[Image:Yellow_estop.jpg]]
-OR
+'''OR'''
 [[Image:Yellow_estop_small.jpg]]
@@ Line 17: / Line 17: @@
 * Ensure the Emergency Stop Switches are disengaged by pressing them in and then rotating them out. Then try to enable the controller again.
-If the problem persists:
+'''If the problem persists:'''
-If your control box has a ready light, while watching the ready light, click to enable the controller. The exact moment you click to enable, the ready light may blink. You may need an assistant to click to enable while you watch the ready light.
+If your control box has a ready light, '''while watching the ready light, click to enable the controller'''. The '''exact moment''' you click to enable, the ready light may blink.
-If the ready light blinks one time like this:
+If the ready light blinks one time like this (this video cycles every 10 seconds, be patient):
 [[Image:Estop_blink.jpg]]

← Older revision		Revision as of 15:51, 1 September 2011
Line 1:		Line 1:
−	~~If you~~ are repeatedly getting one of the following two message boxes:	+	=== Scenario ===
		+
		+	You are repeatedly getting one of the following two message boxes:
		+
		+	[[Image:Yellow_estop.jpg]]
		+
		+	OR
		+
		+	[[Image:Yellow_estop_small.jpg]]
		+
		+	=== Problem ===
		+
		+	The Emergency stop loop has been tripped or the machine is not connected.
		+
		+	=== Solution ===
		+
		+	* Ensure the Emergency Stop Switches are disengaged by pressing them in and then rotating them out. Then try to enable the controller again.
		+
		+	If the problem persists:
		+
		+	If your control box has a ready light, while watching the ready light, click to enable the controller. The exact moment you click to enable, the ready light may blink. You may need an assistant to click to enable while you watch the ready light.
		+
		+	If the ready light blinks one time like this:
		+
		+	[[Image:Estop_blink.jpg]]
		+
		+	The problem is the E-stop loop.
		+	Note that the E-stop loop runs through not only the emergency stop switch, but all of the motors as well. This is done to prevent a dangerous situation.
		+
		+	Follow this link if the Ready light '''DOES blink''' when you attempt to enable. [[Estop_loop_broken]]
		+
		+	Follow this link if the ready link '''does not blink''' when you attempt to enable. [[Estop_noblink]]
		+
		+	Follow this link if you '''do not have a ready light''' on your control box. [[Estop_no_ready_light]]
		+
		+
		+	[[Category:Knowledge Base]]