Mark Pulleys - Revision history

Efeldman at 19:21, 23 April 2012

2012-04-23T19:21:30Z

Efeldman at 19:20, 23 April 2012

2012-04-23T19:20:32Z

Efeldman at 19:20, 23 April 2012

2012-04-23T19:20:12Z

Efeldman at 19:19, 23 April 2012

2012-04-23T19:19:44Z

Efeldman at 19:17, 23 April 2012

2012-04-23T19:17:01Z

Efeldman at 19:16, 23 April 2012

2012-04-23T19:16:08Z

Efeldman: Created page with "'''Marking pulleys''' Marking pulleys is used to determine whether or not the pulleys are slipping on the motor or ball screw shafts. Drifting pulleys can be responsible for ma..."

2012-04-23T19:15:40Z

Created page with "'''Marking pulleys''' Marking pulleys is used to determine whether or not the pulleys are slipping on the motor or ball screw shafts. Drifting pulleys can be responsible for ma..."

New page

'''Marking pulleys'''

Marking pulleys is used to determine whether or not the pulleys are slipping on the motor or ball screw shafts. Drifting pulleys can be responsible for machine drift.

Step 1: Mark the pulleys in one of two ways:

[[File:marked shaft end.jpg]]

[[File:marked shaft side.jpg]]

Step 2: Run the file or perform the operation that would cause the drift issue.

Step 3: Check the pulleys. If the lines no longer line up, the pulley has slipped. Remove, inspect, replace if necessary, and reassemble properly to prevent this from happening again.

← Older revision		Revision as of 19:21, 23 April 2012
Line 4:		Line 4:

	'''NOTE: THERE IS A MARK ON BOTH THE PULLEY AND THE SHAFT INSIDE THE PULLEY.'''		'''NOTE: THERE IS A MARK ON BOTH THE PULLEY AND THE SHAFT INSIDE THE PULLEY.'''
		+
		+	'''NOTE: MARK BOTH PULLEYS IF PRESENT - THE MOTOR SIDE AND THE BALL SCREW SIDE. IF THERE IS ONLY A SHAFT COUPLING, MARK BOTH SIDES OF THE SHAFT COUPLING.'''

@@ Line 1: / Line 1: @@
 Marking pulleys is used to determine whether or not the pulleys are slipping on the motor or ball screw shafts. Drifting pulleys can be responsible for [[Drift_test|machine drift]].
-'''Step 1: Mark the pulleys in one of two ways:
+'''Step 1: Mark the pulleys in one of two ways:'''
-NOTE: THERE IS A MARK ON BOTH THE PULLEY AND THE SHAFT INSIDE THE PULLEY.'''
+'''NOTE: THERE IS A MARK ON BOTH THE PULLEY AND THE SHAFT INSIDE THE PULLEY.'''
@@ Line 10: / Line 10: @@
 [[File:marked shaft side.jpg]]
-'''Step 2: Run the file or perform the operation that would cause the drift issue.
+'''Step 2: Run the file or perform the operation that would cause the drift issue.'''
-Step 3: Check the pulleys. If the lines no longer line up, the pulley has slipped. Remove, inspect, replace if necessary, and reassemble properly to prevent this from happening again.'''
+'''Step 3: Check the pulleys. If the lines no longer line up, the pulley has slipped. Remove, inspect, replace if necessary, and reassemble properly to prevent this from happening again.'''

@@ Line 1: / Line 1: @@
 Marking pulleys is used to determine whether or not the pulleys are slipping on the motor or ball screw shafts. Drifting pulleys can be responsible for [[Drift_test|machine drift]].
-Step 1: Mark the pulleys in one of two ways:
+'''Step 1: Mark the pulleys in one of two ways:
-NOTE: THERE IS A MARK ON BOTH THE PULLEY AND THE SHAFT INSIDE THE PULLEY.
+NOTE: THERE IS A MARK ON BOTH THE PULLEY AND THE SHAFT INSIDE THE PULLEY.'''
@@ Line 10: / Line 10: @@
 [[File:marked shaft side.jpg]]
-Step 2: Run the file or perform the operation that would cause the drift issue.
+'''Step 2: Run the file or perform the operation that would cause the drift issue.
-Step 3: Check the pulleys. If the lines no longer line up, the pulley has slipped. Remove, inspect, replace if necessary, and reassemble properly to prevent this from happening again.
+Step 3: Check the pulleys. If the lines no longer line up, the pulley has slipped. Remove, inspect, replace if necessary, and reassemble properly to prevent this from happening again.'''

← Older revision		Revision as of 19:19, 23 April 2012
Line 2:		Line 2:

	Step 1: Mark the pulleys in one of two ways:		Step 1: Mark the pulleys in one of two ways:
		+
		+	NOTE: THERE IS A MARK ON BOTH THE PULLEY AND THE SHAFT INSIDE THE PULLEY.
		+

	[[File:marked shaft end.jpg]]		[[File:marked shaft end.jpg]]

← Older revision		Revision as of 19:17, 23 April 2012
Line 1:		Line 1:
−	~~'''Marking pulleys'''~~
−
−
	Marking pulleys is used to determine whether or not the pulleys are slipping on the motor or ball screw shafts. Drifting pulleys can be responsible for [[Drift_test\|machine drift]].		Marking pulleys is used to determine whether or not the pulleys are slipping on the motor or ball screw shafts. Drifting pulleys can be responsible for [[Drift_test\|machine drift]].

← Older revision		Revision as of 19:16, 23 April 2012
Line 2:		Line 2:


−	Marking pulleys is used to determine whether or not the pulleys are slipping on the motor or ball screw shafts. Drifting pulleys can be responsible for machine drift.	+	Marking pulleys is used to determine whether or not the pulleys are slipping on the motor or ball screw shafts. Drifting pulleys can be responsible for [[Drift_test\|machine drift]].

	Step 1: Mark the pulleys in one of two ways:		Step 1: Mark the pulleys in one of two ways: