Outputs while moving - Revision history

Efeldman at 22:04, 28 November 2011

2011-11-28T22:04:52Z

Efeldman at 22:02, 28 November 2011

2011-11-28T22:02:52Z

Efeldman at 19:59, 21 November 2011

2011-11-21T19:59:43Z

Efeldman at 19:53, 21 November 2011

2011-11-21T19:53:29Z

Efeldman at 19:53, 21 November 2011

2011-11-21T19:53:03Z

Efeldman at 19:51, 21 November 2011

2011-11-21T19:51:39Z

Efeldman at 19:49, 21 November 2011

2011-11-21T19:49:15Z

Efeldman at 19:44, 21 November 2011

2011-11-21T19:44:39Z

Efeldman: M98 and M99 output bank operations

2011-11-21T19:43:57Z

M98 and M99 output bank operations

New page

'''Toggling Outputs while moving in G-code'''

In certain applications, it is necessary to toggle outputs while moving in gcode without slowing down or stopping.

This is especially popular in gluing applications, as the users typically want to start the move before the glue start, wait until the machine is at speed, and then start the glue. The same goes for stopping the glue -- users typically want to turn it off while at a constant speed, instead of while decelerating.

To perform this function, version 1.423.3 or newer of the CNC interface is necessary.

The command structure is as such:

Move
Output control
Continue the same move
Output control
...

Outputs for this function are numbered from 0 thru 7.

An example is as follows:

<PRE>G0X0Y0Z0
G1 X.5 Y1
M98 CMD OUTA [7,1]
G1 X5.5 Y11
M98 CMD OUTA [7,0]
G1 X6 Y12></PRE>

This will move seamlessly from X,Y,Z=0
to
X=6, Y=12, Z=0
It will turn the glue, at output #7 on at X=.5
It will turn the glue off at X=5.5

If making a circle of glue, the command might look as such:

G0X0Y0Z0
G2 X2 Y2 I2 J0 F100
M98 CMD OUTA [0,1]
G2 X2 Y2 I0 J-2
M98 CMD OUTA [0,0]
G1 X4 Y2

This example will start a 4" circle on the machine origin at 9:00 on the circle.
It will turn the glue on at 12:00 on the circle.
It will turn the glue off at 12:00 on the circle.
It will continue moving linearly to X=3 Y=2 for the decel, so the glue is always laid out at constant speed.
The glue operations were done on the quadrants for the sake of clarity in this example. They can be put anywhere, so long as the math is done properly.

'''Notes:'''

#The software will blend the moves between M98 commands. It will blend these moves no differently than if the code did not have the M98 commands. Corners and other hitches that slowed down the machine before will still slow the machine down similarly. The sole purpose of M98 commands is to perform the actions with no change in G-code.

#Depending on how fast your computer is and how many operations you do
at a time, you may get stuttering on the machine. To investigate,
after running a file, open log.dat inside your cnc interface folder,
and look for text as such:

11-21-2011 13:52:59 END m98outa.nc
11-21-2011 13:52:59 closing #8
11-21-2011 13:53:13 There were 3 Computer speed issues with running that file.
Contact technical support and give them this code: 050110/3
11-21-2011 13:53:13 3 Of those computer speed issues were due to M98 commands.

Ideally, you'll see 0 computer speed issues. If you get more than 0, it might not be a problem. Contact Techno Engineering to discuss. Be prepared to provide your files by email.

#M99 commands are parsed just like M98 commands, however, the machine will slow down to a stop to perform them. This is the only difference.

@@ Line 61: / Line 61: @@
 The software will blend the moves between M98 commands. It will blend these moves no differently than if the code did not have the M98 commands. Corners and other hitches that slowed down the machine before will still slow the machine down similarly. The sole purpose of M98 commands is to perform the actions with no change in G-code.
-If there is an M98 command just before a move that would result in a stop, sometimes the stop will be eliminated. The following code will result in a high-accel bounce at 3 units:
+If there is an M98 command just before a move that would result in a stop, sometimes the stop will be eliminated. The following code will result in a high-accel bounce at 3 units when it also turns the output:
 <pre>

← Older revision		Revision as of 22:02, 28 November 2011
Line 60:		Line 60:

	The software will blend the moves between M98 commands. It will blend these moves no differently than if the code did not have the M98 commands. Corners and other hitches that slowed down the machine before will still slow the machine down similarly. The sole purpose of M98 commands is to perform the actions with no change in G-code.		The software will blend the moves between M98 commands. It will blend these moves no differently than if the code did not have the M98 commands. Corners and other hitches that slowed down the machine before will still slow the machine down similarly. The sole purpose of M98 commands is to perform the actions with no change in G-code.
		+
		+	If there is an M98 command just before a move that would result in a stop, sometimes the stop will be eliminated. The following code will result in a high-accel bounce at 3 units:
		+
		+	<pre>
		+	G90
		+
		+	G1X0Y0Z0
		+	G1X3 F100
		+	M98 CMD OUTA [1,1]
		+	G1X0
		+	M30
		+	</pre>
		+
		+	To fix this, move the M98 command to before the return command, as such:
		+
		+	<pre>
		+	G90
		+
		+	G1X0Y0Z0
		+	G1X2.999 F100
		+	M98 CMD OUTA [1,1]
		+	G1X3
		+	G1X0
		+	M30
		+	</pre>

	Depending on how fast your computer is and how many operations you do at a time, you may get stuttering on the machine. To investigate, after running a file, open log.dat inside your cnc interface folder, and look for text as such:		Depending on how fast your computer is and how many operations you do at a time, you may get stuttering on the machine. To investigate, after running a file, open log.dat inside your cnc interface folder, and look for text as such:

← Older revision		Revision as of 19:53, 21 November 2011
Line 72:		Line 72:
	Ideally, you'll see 0 computer speed issues. If you get more than 0, it might not be a problem. Contact Techno Engineering to discuss. Be prepared to provide your files by email.		Ideally, you'll see 0 computer speed issues. If you get more than 0, it might not be a problem. Contact Techno Engineering to discuss. Be prepared to provide your files by email.

−	#M99 commands are parsed just like M98 commands, however, the machine will slow down to a stop to perform them. This is the only difference.	+	M99 commands are parsed just like M98 commands, however, the machine will slow down to a stop to perform them. This is the only difference.

@@ Line 52: / Line 52: @@
 It will turn the glue off at 12:00 on the circle.
-It will continue moving linearly to X=3 Y=2 for the decel, so the glue is always laid out at constant speed.
+It will continue moving linearly to X=4 Y=2 for the decel, so the glue is always laid out at constant speed.
 The glue operations were done on the quadrants for the sake of clarity in this example. They can be put anywhere, so long as the math is done properly.

@@ Line 59: / Line 59: @@
 '''Notes:'''
-#The software will blend the moves between M98 commands. It will blend these moves no differently than if the code did not have the M98 commands. Corners and other hitches that slowed down the machine before will still slow the machine down similarly. The sole purpose of M98 commands is to perform the actions with no change in G-code.
+The software will blend the moves between M98 commands. It will blend these moves no differently than if the code did not have the M98 commands. Corners and other hitches that slowed down the machine before will still slow the machine down similarly. The sole purpose of M98 commands is to perform the actions with no change in G-code.
-#Depending on how fast your computer is and how many operations you do at a time, you may get stuttering on the machine. To investigate, after running a file, open log.dat inside your cnc interface folder, and look for text as such:
 <PRE>

@@ Line 3: / Line 3: @@
 In certain applications, it is necessary to toggle outputs while moving in gcode without slowing down or stopping.
-This is especially popular in gluing applications, as the users typically want to start the move before the glue start, wait until the machine is at speed, and then start the glue. The same goes for stopping the glue -- users typically want to turn it off while at a constant speed, instead of while decelerating.
+This is especially popular in gluing applications, as the users typically want to start the move before the glue starts, wait until the machine is at speed, and then start the glue. The same goes for stopping the glue -- users typically want to turn it off while at a constant speed, instead of while decelerating.
 To perform this function, version 1.423.3 or newer of the CNC interface is necessary.
@@ Line 11: / Line 11: @@
 Move
 Output control
-Continue the same move
+Continue the move along similar trajectory
 Output control
 ...
-Outputs for this function are numbered from 0 thru 7.
+Outputs for this function are numbered from 0 thru 7. They are in diagnostics listed as Coolant -> speed con 3
-An example is as follows:
+'''An example is as follows:'''
 <PRE>G0X0Y0Z0
@@ Line 27: / Line 27: @@
 This will move seamlessly from X,Y,Z=0
 to
 X=6, Y=12, Z=0
 It will turn the glue, at output #7 on at X=.5
 It will turn the glue off at X=5.5
 If making a circle of glue, the command might look as such:
 <PRE>G0X0Y0Z0
@@ Line 42: / Line 47: @@
 This example will start a 4" circle on the machine origin at 9:00 on the circle.
 It will turn the glue on at 12:00 on the circle.
 It will turn the glue off at 12:00 on the circle.
 It will continue moving linearly to X=3 Y=2 for the decel, so the glue is always laid out at constant speed.
 The glue operations were done on the quadrants for the sake of clarity in this example. They can be put anywhere, so long as the math is done properly.
 '''Notes:'''
@@ Line 56: / Line 66: @@
 and look for text as such:
 -21-2011 13:52:59 END   m98outa.nc
 -21-2011 13:52:59 closing #8
@@ Line 61: / Line 72: @@
      Contact technical support and give them this code: 050110/3
 -21-2011 13:53:13  3 Of those computer speed issues were due to M98 commands.
 Ideally, you'll see 0 computer speed issues. If you get more than 0, it might not be a problem. Contact Techno Engineering to discuss. Be prepared to provide your files by email.
 #M99 commands are parsed just like M98 commands, however, the machine will slow down to a stop to perform them. This is the only difference.

@@ Line 34: / Line 34: @@
 If making a circle of glue, the command might look as such:
-G0X0Y0Z0
+<PRE>G0X0Y0Z0
 G2 X2 Y2 I2 J0 F100
 M98 CMD OUTA [0,1]
 G2 X2 Y2 I0 J-2
 M98 CMD OUTA [0,0]
-G1 X4 Y2
+G1 X4 Y2</PRE>
 This example will start a 4" circle on the machine origin at 9:00 on the circle.