Set Tool Length Offsets Tutorial - Revision history

Efeldman at 20:54, 18 September 2011

2011-09-18T20:54:38Z

Efeldman at 15:34, 29 July 2011

2011-07-29T15:34:38Z

Jbeck at 19:46, 15 December 2010

2010-12-15T19:46:07Z

Jbeck at 16:22, 7 October 2010

2010-10-07T16:22:02Z

Jbeck at 16:12, 7 October 2010

2010-10-07T16:12:13Z

Jbeck at 15:54, 7 October 2010

2010-10-07T15:54:36Z

Jbeck: Created page with "In order to be able to change tools during a file and continue to cut at the proper depth, the machine must be told how long each tool is. This article describes how to measure t..."

2010-10-07T15:53:29Z

Created page with "In order to be able to change tools during a file and continue to cut at the proper depth, the machine must be told how long each tool is. This article describes how to measure t..."

New page

In order to be able to change tools during a file and continue to cut at the proper depth, the machine must be told how long each tool is. This article describes how to measure the tool length and save it for later use.

=== Measure an Empty Tool Holder ===

This empty tool holder will be our reference point.

# Place the touchpad on a stable spot on the table. If possible, choose a spot that can be easily used again in the future, one which will not change.
# Remove the collet nut and tool from a tool holder, leaving a completely empty tool holder in the chuck.
# Position this empty tool holder over the touch pad and click on "Learn Empty Tool". This will measure the reference point.

=== Measure Your Tools ===
# Change tools to the one you will measure first. This can be done through a manual tool change or an automatic one. If it is done manually, be certain to identify the tool in the chuck to the software.
# Position the tool over the touchpad, leaving anywhere from 0.1" to 1" between the tool and the pad.
# In the main screen, click TOOL, and then click on "Learn tool #x" where X is the number of the tool currently in the chuck. If x is not the tool in the chuck, it was not properly identified, and will not be learned correctly.
# The tool will slowly drop until it touches the pad, and then retract. The tool has been learned.

Measure the rest of the tools until the software knows the lengths of all your tools.

=== Tool Types and Special Tool Setup ===

There are many different types of tool retrieval methods available. Tools can be numbered 1 thru 255.

# Tool in tool holder, which has a stand - this is the most common type of tool.
# Tool in a drill bank or piggy back drill which has no stand - only an XY offset from the main tool.
# Tool on the 4th axis - will have an XY offset from the main tool
# Tool in tool holder, which has a stand not accessable through normal pickup methods
# Tool Macro - not really a tool, so much as a process that needs to be performed during gcode, but relative to HOME instead of ZERO.

To set up these types of tools, follow these instructions:

To set up tool style #1, nothing special must be done.

To set up tool style #2 and #3, measure the XY offset between the main tool holder and the unit, then put these numbers in the tool grid. Number the special column 10.

To set up tool style #4, create a tool pickup file as per the instructions in the manual. If the tool number is less than 150, number the Special column 15. If the tool is greater than 150, nothing else needs to be done. This type of tool can not be numbered 200 or greater.

To set up tool style #5, create a tool macro file as per the instructions in the manual. Number the tool 200 or greater.

The key difference between a custom tool numbered 151-199 and 200-255 is that tools numbered 151-199 will drop off previous tools before performing the pickup sequence, and tools 200-255 will not drop off previous tools.

[[Category:Software Manual (servo)]]
[[Category:Tutorials]]

@@ Line 1: / Line 1: @@
 {{ManualNavigation (servo)}}
-{{CSVersion|version=1.420|comment=and after}}
+{{CSVersion|version=1.418|comment=and after}}
 In order to be able to change tools during a file and continue to cut at the proper depth, the machine must be told how long each tool is. This article describes how to measure the tool length and save it for later use.

← Older revision		Revision as of 16:12, 7 October 2010
Line 1:		Line 1:
	{{ManualNavigation (servo)}}		{{ManualNavigation (servo)}}
		+
		+	{{CSVersion\|version=1.420\|comment=and after}}

	In order to be able to change tools during a file and continue to cut at the proper depth, the machine must be told how long each tool is. This article describes how to measure the tool length and save it for later use.		In order to be able to change tools during a file and continue to cut at the proper depth, the machine must be told how long each tool is. This article describes how to measure the tool length and save it for later use.

← Older revision		Revision as of 15:54, 7 October 2010
Line 1:		Line 1:
		+	{{ManualNavigation (servo)}}
		+
	In order to be able to change tools during a file and continue to cut at the proper depth, the machine must be told how long each tool is. This article describes how to measure the tool length and save it for later use.		In order to be able to change tools during a file and continue to cut at the proper depth, the machine must be told how long each tool is. This article describes how to measure the tool length and save it for later use.

@@ Line 10: / Line 10: @@
 # Place the touchpad on a stable spot on the table. If possible, choose a spot that can be easily used again in the future, one which will not change.
-# Remove the collet nut and tool from a tool holder, leaving a completely empty tool holder in the chuck.
+# Remove the collet nut, collet and tool from a tool holder, leaving a completely empty tool holder in the chuck.
-# Position this empty tool holder over the touch pad and click on "Learn Empty Tool". This will measure the reference point.
+# Position this empty tool holder over the touch pad and click on the "Tools" button, then  "Empty". This will measure the reference point.
 === Measure Your Tools ===
 Single Tool Method:
 # Change tools to the one you will measure first. This can be done through a manual tool change or an automatic one. If it is done manually, be certain to identify the tool in the chuck to the software.
-# Position the tool over the touchpad, leaving anywhere from 0.1" to 1" between the tool and the pad.
+# Position the tool over the touchpad, in the same spot the empty tool was learned. Leave anywhere from 0.1" to 1" between the tool and the pad.
 # In the main screen, click TOOL, and then click on "Learn tool #x" where X is the number of the tool currently in the chuck. If x is not the tool in the chuck, it was not properly identified, and will not be learned correctly.
 # The tool will slowly drop until it touches the pad, and then retract. The tool has been learned.
 Measure the rest of the tools until the software knows the lengths of all your tools.
 Multi Tool Method:

@@ Line 42: / Line 42: @@
 The key difference between a custom tool numbered 151-199 and 200-255 is that tools numbered 151-199 will drop off previous tools before performing the pickup sequence, and tools 200-255 will not drop off previous tools.
 [[Category:Software Manual (servo)]]
 [[Category:Tutorials]]