http://www.docs.technorouters.com/index.php?action=history&feed=atom&title=Setting_up_an_old_teco_inverter 2026-07-18T11:56:43Z Revision history for this page on the wiki MediaWiki 1.24.4 http://www.docs.technorouters.com/index.php?title=Setting_up_an_old_teco_inverter&diff=1767&oldid=prev 2011-10-03T14:48:25Z

<p>Created page with &quot;&#039;&#039;&#039;Inverter Settings for Motortronics or Teco inverters&#039;&#039;&#039; For Spindles up to 10HP The following settings must be set. All others should be left set to the factory defaults as ...&quot;</p> <p><b>New page</b></p><div>'''Inverter Settings for Motortronics or Teco inverters'''<br /> <br /> For Spindles up to 10HP<br /> <br /> The following settings must be set. All others should be left set to the<br /> factory defaults as indicated in the inverter manual.<br /> <br /> Press “Display Func”<br /> <br /> You get F000 – this means “Function 0”<br /> <br /> Increment using the arrow keys to the appropriate value. Press Enter<br /> <br /> Using the up, down, and left/reset arrows, set the value. Press Enter<br /> <br /> Repeat for each necessary function<br /> <br /> 1: 0.9<br /> <br /> 2: 0.9<br /> <br /> 3: 0100<br /> <br /> 5: 18<br /> <br /> 6: 300 see note 1.<br /> <br /> 7: 100 see note 2.<br /> <br /> 10: 1 - start/stop from program.<br /> <br /> 11: 1 - speed set from potentiometer or ATC speed control<br /> <br /> 12: 1<br /> <br /> 17: 100.0<br /> <br /> 18: 133.0<br /> <br /> 19: 166.0<br /> <br /> 20: 200.0 Functions 17 through 23 are for TOOLCHANGER machines only<br /> <br /> 21: 233.0<br /> <br /> 22: 266.0<br /> <br /> 23: 300.0<br /> <br /> 25: set same as function 6<br /> <br /> 37: set same as function 6<br /> <br /> 70: set to motor rated current on motor nameplate for appropriate voltage<br /> <br /> <br /> '''note 1''': Function 6 is the maximum output frequency this should be set to the maximum<br /> rated frequency of the spindle. This is normally 300 for 18,000 RPM spindles or 400 for<br /> 24,000 RPM spindles. Consult spindle documentation and motor nameplate for<br /> maximum frequency.<br /> <br /> '''note 2''': Function 7 is the lower output frequency limit. The minimum for 18,000 RPM<br /> and 24,000 RPM spindles is 100 which corresponds to 6000 rpm. Operating at speeds<br /> below this may cause motor overheating and damage to the motor. Consult spindle<br /> documentation and motor nameplate for lower frequency rating.<br /> <br /> '''note 3''': For analog speed control on riser card<br /> <br /> Function 11 = 2<br /> Function 26 = 98<br /> Function 28 is approximately 84, plus/minus 2 depending on the computer. (lower #28 makes top speed faster)<br /> <br /> <br /> ----<br /> <br /> <br /> MA 7200 Inverter:<br /> <br /> BN1 0.9 acc<br /> BN2 0.9 dec<br /> <br /> CN2 300 Max Freq<br /> CN4 300 Full voltage freq<br /> CN9 Current from motor name plate<br /> <br /> SN2 15 V/F profile<br /> SN3 7 Operator initialization<br /> <br /> SN4 1 Control term run source set to 0 for keypad 1 for remote<br /> SN5 0 frequency source keypad<br /> SN8 1 Reverse inhibit<br /> SN67 0 V/F mode<br /> SN25 2 in term 5 2 wire control</div>

Efeldman