From TechnoDocs
(→Setup Commands) |
|||
| Line 64: | Line 64: | ||
|- | |- | ||
| − | | | + | |M6 |
| − | | | + | |Tool Change |
| − | | | + | |M6 T<#> |
| − | | | + | |Requests the machine change to the specified tool number. It will turn off the spindle and coolant and other required operations when it changes the tool. |
|- | |- | ||
| − | | | + | |M7 or M8 |
| − | | | + | |Coolant On |
| − | | | + | |M7 or M8 |
| − | | | + | |Turns the coolant flow on. |
|- | |- | ||
| − | | | + | |M9 |
| − | | | + | |Coolant Off |
| − | | | + | |M9 |
| − | | | + | |Turns the coolant flow off. |
|- | |- | ||
| − | | | + | |M90 |
| − | | | + | |Output Off |
| − | | | + | |M90 OUT<#> |
| − | | | + | |Turns the output to the Off or 0 state. |
|- | |- | ||
| − | | | + | |M91 |
| − | | | + | |Output On |
| − | | | + | |M91 OUT<#> |
| − | | | + | |Turns the output to the On or 1 state. |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
|} | |} | ||
| − | |||
== Routing Commands == | == Routing Commands == | ||
Revision as of 12:12, 1 October 2010
The following G and M codes are supported by the Control Interface.
Setup Commands
| Code | Command | Format | Purpose |
|---|---|---|---|
| F | Feed Speed | F<speed> | Sets the feed rate, or rate of movement of the axes. |
| G4 | Dwell Time | G4 P<milliseconds> | Inserts a delay in milliseconds. |
| G90 | Absolute Coordinates | G90 | Sets coordinates to absolute, so that the motion commands are relative to the origin. |
| G91 | Incremental Coordinates | G90 | Sets coordinates to incremental so that all motion commands are relative to the previous position. |
| G92 | Set Absolute Origin | G92 X<#> Y<#> Z<#> | Sets the origin that is referenced when in absolute mode. |
| M0 | Program Stop/Pause | M0 | Stops the g-code file from being further processed until the operator presses Continue or Start. |
| M30 | End of Data | M30 | Marks the end of the file. The rest of the file will not be processed. |
| M3 or M4 | Spindle On | M3 or M4 | Starts the spindle. |
| M5 | Spindle Off | M5 | Turns the spindle off. |
| M6 | Tool Change | M6 T<#> | Requests the machine change to the specified tool number. It will turn off the spindle and coolant and other required operations when it changes the tool. |
| M7 or M8 | Coolant On | M7 or M8 | Turns the coolant flow on. |
| M9 | Coolant Off | M9 | Turns the coolant flow off. |
| M90 | Output Off | M90 OUT<#> | Turns the output to the Off or 0 state. |
| M91 | Output On | M91 OUT<#> | Turns the output to the On or 1 state. |
Routing Commands
| Code | Command | Format | Purpose |
|---|---|---|---|
Drill Cycle Commands
| Code | Command | Format | Purpose |
|---|---|---|---|