From TechnoDocs
- 09:50, 14 March 2012 (diff | hist) . . (+111) . . Measuring the offset between the knife and the spindle (current)
- 08:37, 14 March 2012 (diff | hist) . . (+80) . . Measuring the offset between the knife and the spindle
- 07:28, 14 March 2012 (diff | hist) . . (-8) . . Measuring the offset between the knife and the spindle
- 07:25, 14 March 2012 (diff | hist) . . (+99) . . Measuring the offset between the knife and the spindle
- 14:43, 13 March 2012 (diff | hist) . . (-2) . . Measuring the offset between the knife and the spindle
- 14:36, 13 March 2012 (diff | hist) . . (+41) . . Measuring the offset between the knife and the spindle
- 14:31, 13 March 2012 (diff | hist) . . (0) . . N File:Knife cutting cross low res.jpg (current)
- 14:30, 13 March 2012 (diff | hist) . . (0) . . File:Vcuttercalibration.jpg (uploaded a new version of "File:Vcuttercalibration.jpg") (current)
- 14:14, 13 March 2012 (diff | hist) . . (+47) . . Measuring the offset between the knife and the spindle
- 14:13, 13 March 2012 (diff | hist) . . (0) . . File:Cross cut.JPG (uploaded a new version of "File:Cross cut.JPG") (current)
- 13:28, 13 March 2012 (diff | hist) . . (0) . . File:Cross cut.JPG (uploaded a new version of "File:Cross cut.JPG": image with lower resolution)
- 13:26, 13 March 2012 (diff | hist) . . (0) . . File:Cross cut.JPG (uploaded a new version of "File:Cross cut.JPG": same photo with lower resolution)
- 13:15, 13 March 2012 (diff | hist) . . (+35) . . N File:Vcuttercalibration.jpg (Measuring offset using a 'V' cutter)
- 13:00, 13 March 2012 (diff | hist) . . (0) . . File:Cross cut.JPG (uploaded a new version of "File:Cross cut.JPG")
- 12:58, 13 March 2012 (diff | hist) . . (+61) . . N File:Cross cut.JPG (The cross cut seen above was done using an oscillating knife.)
- 10:51, 13 March 2012 (diff | hist) . . (+1,126) . . N Measuring the offset between the knife and the spindle (Created page with "The process consists in using the knife to cut a reference mark (e.g. a cross), and then jogging the spindle to the respective reference mark. The router's current position is th...")
- 10:50, 13 March 2012 (diff | hist) . . (+21) . . Control Software (I-Cut Integration) (current)
- 10:49, 13 March 2012 (diff | hist) . . (+13) . . Control Software (I-Cut Integration)
- 10:47, 13 March 2012 (diff | hist) . . (+12) . . N Category:Control Software (I-Cut Integration) (Created page with "{{Category}}") (current)
- 10:14, 13 March 2012 (diff | hist) . . (-49) . . Control Software (I-Cut Integration)
- 10:10, 13 March 2012 (diff | hist) . . (+12) . . Control Software (I-Cut Integration)
- 10:08, 13 March 2012 (diff | hist) . . (-20) . . Control Software (I-Cut Integration)
- 10:08, 13 March 2012 (diff | hist) . . (+270) . . N Control Software (I-Cut Integration) (Created page with "This manual will guide you through the set up and operation of your I-Cut/Techno integration system. == Table of Contents == == Installation == == Setup == # [[Knife/Spindle ...")
- 09:58, 13 March 2012 (diff | hist) . . (+81) . . Software manual (current)
- 11:03, 5 May 2011 (diff | hist) . . (0) . . Toggle between rotary and lathe buttons
- 10:46, 5 May 2011 (diff | hist) . . (+21) . . Toggle between rotary and lathe buttons
- 10:39, 5 May 2011 (diff | hist) . . (-23) . . Toggle between rotary and lathe buttons
- 10:37, 5 May 2011 (diff | hist) . . (+422) . . N Toggle between rotary and lathe buttons (Created page with "{{Control Software (lathe)|Techno Lathe Manual}} {{WIP}} This feature allows us to display the lathe or rotary buttons. In order to achieve this, we need to: * Go into ''Setu...")
- 10:27, 5 May 2011 (diff | hist) . . (+46) . . Control Software (lathe) (current)
- 07:02, 23 March 2011 (diff | hist) . . (+68) . . G-code reference (→Setup Commands)
- 09:38, 4 January 2011 (diff | hist) . . (-6) . . Control Software (servo) (current)
- 09:36, 4 January 2011 (diff | hist) . . (+6) . . Control Software (servo)
- 09:27, 4 January 2011 (diff | hist) . . (0) . . Parallel Z & A axes (current)
- 09:26, 4 January 2011 (diff | hist) . . (+602) . . N Parallel Z & A axes (Created page with "{{ManualNavigation (servo)}} {{WIP}} In order to set up parallel A & Z axes with their respective end effectors (e.g. spindle and drill bank), follow the steps below: * Open ...")
- 08:31, 4 January 2011 (diff | hist) . . (+26) . . Control Software (servo) (Parallel A & Z axes info added)
- 09:38, 9 November 2010 (diff | hist) . . (0) . . G-code reference
- 09:08, 28 October 2010 (diff | hist) . . (+21) . . Park Position (current)
- 08:55, 27 October 2010 (diff | hist) . . (+7) . . Park Position
- 08:53, 27 October 2010 (diff | hist) . . (+94) . . Park Position
- 08:38, 27 October 2010 (diff | hist) . . (+20) . . Control Software (servo)
- 08:37, 27 October 2010 (diff | hist) . . (+590) . . N Park Position (Created page with "{{ManualNavigation (servo)}} {{WIP}} The Park feature allows us to save a specific location, and then return to the position whenever needed. In order to achieve this, we need...")
- 07:33, 20 October 2010 (diff | hist) . . (+1,145) . . N Progress Bar or Current Position is not updated (Created page with "=== Scenario === When running a File, the Progress Bar or the Current Position is not being updated. === Problem === There is a setup issue. The settings in the Techno CNC Inter...")